[. . . ] Avoid using outlets on the same circuit as photocopiers or air control systems that regularly switch on and off. Safety Instructions 3 Epson AcuLaser CX37 Series Safety Information Guide ❏ Connect your printer to an electrical outlet that meets the power requirements of this printer. Your printer’s power requirements are indicated on a label attached to the printer. If you are not sure of the power supply specifications in your area, contact your local power company or consult your dealer. [. . . ]  Slots and openings in the cabinet and the back or bottom are provided for ventilation. Do not put the printer on a bed, sofa, rug, or other similar surface or in a built-in installation unless proper ventilation is provided.  Keep the entire computer and printer system away from potential sources of interference, such as loudspeakers or the base units of cordless telephones.  Leave adequate room around the printer to allow for sufficient ventilation. Safety Instructions 4 Epson AcuLaser CX37 Series Safety Information Guide Using the printer ❏ Be careful not to touch the fuser, which is marked CAUTION, or the surrounding areas. If the printer has been in use, the fuser and the surrounding areas may be very hot. If you must touch one of these areas, wait 40 minutes to allow the heat to subside before doing so. * CAUTION ❏ Do not insert your hand deep into the fuser unit as some components are sharp and may cause injury.  Never push objects of any kind through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a risk of fire or electric shock. Although the printer is designed to be sturdy, rough handling can damage it.  Adjust only those controls that are covered by the operating instructions.  When removing the imaging cartridge, do not expose it to sunlight at all and avoid exposing it to room light for more than five minutes. Exposure to light can damage the drum, causing dark or light areas to appear on the printed page and reducing the service life of the drum. If you need to keep the imaging cartridge out of the printer for long periods, cover it with an opaque cloth. When you remove the imaging cartridge from the printer, always place it on a clean, smooth surface. Avoid touching the drum, since oil from your skin can permanently damage its surface and affect print quality.  Do not let the paper’s edge slide across your skin because the edge of the paper may cut you. Safety Information Laser safety labels w Warning: The performance of procedures and adjustments other than those specified in the printer’s documentation may result in hazardous radiation exposure. Your printer is a Class 1 laser product as defined in the IEC60825 specifications. A label similar to the one shown below is attached to the back of the printer in countries where required. Safety Instructions 7 Epson AcuLaser CX37 Series Safety Information Guide Internal laser radiation There is a Class III b Laser Diode Assembly that has an invisible laser beam inside the printer head unit. The printer head unit is NOT A SERVICE ITEM, therefore, the printer head unit should not be opened under any circumstances. [. . . ] Reducering af risikoen Du bør undgå følgende situationer for at minimere risikoen for eksponering med ozon: ❏ Brug af flere laserprintere på begrænset plads ❏ Brug i omgivelser med ekstrem lav fugtighed ❏ Dårlig udluftning af rum ❏ Langvarig, kontinuerlig udskrivning sammen med en af ovennævnte Placering af printer Printeren bør placeres, så de afgivne gasser og varme: ❏ Ikke blæses direkte ind i brugerens ansigt ❏ Sendes direkte ud af bygningen, hvor dette er muligt Standarder og godkendelser Europæisk model: Lavspændingsdirektiv 2006/95/EF EMC-direktiv 2004/108/EF EN60950-1 EN55022 Klasse B EN61000-3-2 EN61000-3-3 EN55024 Sikkerhedsinstruktioner 9 Epson AcuLaser CX37 Series Safety Information Guide R&TTE-direktiv 1999/5/EF (Kun Epson AcuLaser CX37DNF) ES203021-1 ES203021-2 ES203021-3 ES201187 EG201120 EN60950-1 ❏ Til europæiske brugere (Kun Epson AcuLaser CX37DNF): Vi, Seiko Epson Corporation, erklærer herved, at udstyrsmodel L642B er i overensstemmelse med alle grundlæggende krav og andre relevante bestemmelser i Direktiv 1999/5/EF.  Hvis du bruker skjøteledning, må du kontrollere at den totale angitte mengden strøm (ampere) for produktene som er koblet til skjøteledningen, ikke overskrider angitt tillatt strøm for ledningen. Se Printer/Copier/Scanner User’s Guide (Brukerhåndbok for skriver/ kopimaskin/skanner) for veiledning om hvordan du installerer posisjoneringspinnene.  Hold hele datamaskinsystemet borte fra potensielle kilder til forstyrrelser, for eksempel høyttalere og baseenheter for trådløse telefoner. [. . . ]